Scott Aerator Clover Pond Fountain Aerator
The Scott Aerator Clover Delivers a Bigger, Bolder Pond Display
Most pond fountains give you a single spray pattern and call it a day. The Scott Aerator Clover does something different -- its central brass nozzle launches water skyward while four angled side nozzles fan outward at 45 degrees, creating a distinctive clover-shaped spray that looks striking from every angle. On the 1/2 HP, the center stream reaches 20 feet with side jets extending 15 feet. Scale up to the 3 HP and you are looking at a 70-foot center column surrounded by 80-foot angled jets -- a display large enough to anchor a commercial property, HOA pond, or golf course water feature from hundreds of feet away. Flow rates range from 3,600 GPH on the 1/2 HP to 10,200 GPH on the 3 HP, so the Clover isn't just decorative -- it circulates serious water volume, boosts dissolved oxygen, and helps keep algae in check.
Every Clover runs on an oil-free stainless steel submersible motor built in Holland, Michigan. There is no oil to monitor, no control box to wire on the smaller units, and no routine service to schedule. It handles fresh water and salt water equally well, and when winter arrives there is nothing to drain, remove, or winterize. Turn the power off, let the pond freeze around the unit, and flip it back on after the spring thaw with no risk of damage. The 1/2 HP, 3/4 HP, and 1 HP ship in both 115V and 230V, while the 1.5 HP, 2 HP, and 3 HP are 230V only. Every unit includes a submersible 12-gauge power cord, and 115V models come with a standard plug.
Six motor sizes across nine total configurations give you room to match the Clover to anything from a compact backyard pond to a multi-acre lake. Add optional LED light kits -- warm white or color-changing with a wireless remote -- to keep the display running after dark. Plug in an optional timer to control when the motor runs. Use the motor comparison and cable length charts below to zero in on the right configuration for your site.
The Scott Aerator Clover creates a distinctive clover-shaped spray -- a tall center stream surrounded by four angled side jets at 45 degrees. The 1/2 HP reaches 20 feet high with 15-foot side jets, scaling up to a 70-foot center column with 80-foot jets on the 3 HP. Flow rates range from 3,600 to 10,200 GPH, providing real aeration alongside the dramatic display.
The oil-free stainless steel motor runs 24/7 with zero maintenance, handles salt water, and survives winter without removal or winterizing. The three smallest motors come in 115V and 230V, while larger motors are 230V only.
Six HP ratings from 1/2 HP to 3 HP cover ponds from a compact backyard to multi-acre lakes. Add optional LED lights or a timer to customize. Use the charts below to compare motors and confirm cable length.
If this model isn’t ideal, browse our full lineup of Pond Fountains.
Benefits of the Scott Aerator Clover Fountain
Scott Clover Motor Configuration Comparison
| 1/2 HP 115V |
1/2 HP 230V |
3/4 HP 115V |
3/4 HP 230V |
1 HP 115V |
1 HP 230V |
1-1/2 HP 230V |
2 HP 230V |
3 HP 230V |
|
|---|---|---|---|---|---|---|---|---|---|
| Best for Pond Size | 1/8 - 1/4 Acre | 1/4 - 1/2 Acre | 1/2 - 3/4 Acre | 3/4 - 1 Acre | 1 - 1.5 Acres | 1 - 2+ Acres | |||
| Minimum Water Depth | 36" | 44" | 44" | 50" | 56" | 64" | |||
| Center Stream Height | 20' | -- | 30' | 40' | 60' | 70' | |||
| Side Jets Width | 15' | -- | 20' | 20' | 60' | 80' | |||
| Spray Size (H x W) | 20' H x 30' W | 30' H x 35' W | 35' H x 40' W | 40' H x 45' W | 50' H x 60' W | 70' H x 80' W | |||
| Flow Rate | 3,600 GPH | 3,900 GPH | 4,500 GPH | 5,400 GPH | 8,100 GPH | 10,200 GPH | |||
| Amps | 10.0A | 5.0A | 10.7A | 6.8A | 11.5A | 8.2A | 10.6A | 10.0A | 13.3A |
| Est. Operating Cost | $0.06/hr | $0.08/hr | $0.11/hr | $0.17/hr | $0.23/hr | $0.33/hr | |||
| Min. Anchor Weight (each) | 20 lbs | 25 lbs | 25 lbs | 40 lbs | 45 lbs | 55 lbs | |||
| Standard Cord | 70' / 12 GA | 70' / 12 GA | 70' / 12 GA | 70' / 12 GA | 100' / 10 GA | 100' / 10 GA | |||
| Motor Warranty | 5 Years | ||||||||
Key Features of the Clover by Scott Aerator
- Distinctive Clover-Shaped Spray: A central brass nozzle shoots water skyward while four angled side nozzles fan outward at 45 degrees, creating a pattern that looks like a four-leaf clover from above. On the 1/2 HP, the center stream reaches 20 feet with side jets extending 15 feet. On the 3 HP, those numbers jump to 70 feet and 80 feet -- a display that dominates any pond it sits in.
- Oil-Free Stainless Steel Motor: Every Clover runs on an environmentally friendly submersible motor sealed in marine-grade stainless steel. There is no oil to monitor, no filter to replace, and no routine service to schedule. All motors are manufactured in Holland, Michigan and rated for continuous 24-hour operation.
- Six HP Options, Nine Configurations: The 1/2, 3/4, and 1 HP ship in both 115V and 230V. The 1.5, 2, and 3 HP are 230V only. That gives you nine ways to match the Clover to your pond size and electrical setup. Each step up adds spray height, width, and flow rate.
- Factory-Attached Power Cord: Each unit ships ready to connect with a submersible 12-gauge cord (70 feet on motors up to 1.5 HP, 100 feet of 10-gauge on the 2 and 3 HP). The 115V models include a standard plug for residential outlets. Longer replacement cords can be ordered separately.
- No Winterizing, No Removal: All Scott Aerator products are engineered to handle subzero temperatures without any damage to the motor, housing, or float. When the season ends, cut the power and walk away. There is no draining, no storage, and no reinstallation in the spring.
- 15-Minute Installation: The Clover assembles quickly with self-tapping screws and ships with everything you need to get it in the water. Secure two nylon anchoring lines to eyebolts and anchor weights, lower the unit into the pond, and plug it in.
See the Clover Fountain in Action
Maximum Cable Length - Motor to Main Breaker
| Cable Size | 1/2 HP 115V |
1/2 HP 230V |
3/4 HP 115V |
3/4 HP 230V |
1 HP 115V |
1 HP 230V |
1-1/2 HP 230V |
2 HP 230V |
3 HP 230V |
|---|---|---|---|---|---|---|---|---|---|
| 12 AWG | 160' | 650' | 125' | 480' | 75' | 400' | 310' | 250' | 190' |
| 10 AWG | 250' | 1,020' | 150' | 760' | 100' | 630' | 480' | 390' | 300' |
| 8 AWG | 390' | 1,610' | 200' | 1,200' | 150' | 990' | 770' | 620' | 470' |
| 6 AWG | 620' | 2,510' | 350' | 1,870' | 300' | 1,540' | 1,200' | 970' | 750' |
| 4 AWG | 960' | 3,880' | 700' | 2,890' | 650' | 2,380' | 1,870' | 1,530' | 1,190' |
| 2 AWG | 1,460' | 5,880' | 1,100' | 4,370' | 1,050' | 3,610' | 2,850' | 2,360' | 1,850' |
Requirements & What to Know Before You Buy
- Dedicated GFCI Circuit: A GFCI-protected circuit is mandatory for all Clover installations. Have a licensed electrician handle the wiring if you are not sure your current setup meets this requirement.
- Swimmer Safety: Power must be disconnected any time someone enters the water. This applies to all electric pond equipment, not just the Clover.
- Depth Requirements by Motor: The pond must be at least 36" deep for the 1/2 HP, 44" for the 3/4 HP and 1 HP, 50" for the 1.5 HP, 56" for the 2 HP, and 64" for the 3 HP. Measure at the planned placement point, not at the shoreline.
- Two-Point Anchoring: The Clover requires two anchor weights (or concrete blocks) and two nylon mooring ropes to hold position. Minimum weight per anchor ranges from 20 lbs on the 1/2 HP to 55 lbs on the 3 HP. Anchors and rope are sold separately.
- No Extension Cords Allowed: Running the motor through an extension cord is not permitted. If the included power cord does not reach your breaker panel, use the cable length chart above to select the correct wire gauge for the total run distance, and order a longer cord or have a qualified electrician install a dedicated line.
- Choosing 115V or 230V: The 1/2, 3/4, and 1 HP motors come in both voltages. A 115V unit plugs into any standard outlet. A 230V unit needs to be hardwired into a panel. Scott Aerator strongly recommends the 230V version for the 1 HP to avoid voltage drop over longer cord runs. The 1.5 HP, 2 HP, and 3 HP are 230V only.
- Winter Storage Not Needed: Leave the Clover in the pond through the off-season. Cut power, let ice form, and restore power once things thaw. Every part of the unit handles subzero conditions without sustaining damage.
- Salt Water Compatible: The stainless steel motor housing is rated for salt water and brackish ponds out of the box. No coatings, sleeves, or add-on kits are required.
- Continuous Duty Motor: The Clover is rated to run nonstop, day and night, with no breaks and no maintenance intervals. If you want to cycle the motor on and off, an optional timer is available.
- ARL Compliance: Every Clover configuration is ARL tested and approved to meet the applicable requirements of UL and the National Electric Code as a complete package.
What's Included & Optional Add-Ons
- In the Box: Fountain pump with brass nozzle assembly, float platform, stainless steel filter basket, self-tapping assembly screws, submersible power cord (length and gauge depend on motor selection), and owner's manual. Everything needed to get the Clover in the water ships together.
- Available Separately - LED Lights: Choose from Night Glo warm white or color-changing LED sets. Both screw directly onto the float and run off 115V household power. Go with a 2-light set for motors up to 1 HP, or a 4-light set for 1.5 HP and above. Every light set includes a built-in timer. The color-changing version also ships with a wireless remote rated for up to 300 feet.
- Available Separately - Motor Timers: Set the fountain to run on a custom schedule using a mechanical-dial timer with multiple on/off positions. Pick 115V (plug-in) or 230V (hardwired), both in a weather-resistant housing. Timers control the motor only; the light kits handle their own scheduling independently.
- Available Separately - Anchors & Mooring Line: Two anchor weights (or concrete blocks) and two nylon ropes are required to hold the Clover in position. These are not included in the package and must be sourced before installation.
- Available Separately - Extended Power Cords: If your breaker panel sits farther from the pond than the factory cord can reach, longer submersible replacement cords are available in the same gauge as the original.
Scott Aerator Clover Aerating Fountain Specifications
| Manufacturer | Scott Aerator |
| Product Type | Display Pond Fountain |
| Motor Options | 1/2 HP, 3/4 HP, 1 HP, 1.5 HP, 2 HP, 3 HP |
| Voltage Options | 115V and 230V on 1/2, 3/4, and 1 HP; 230V only on 1.5, 2, and 3 HP |
| Total Configurations | 9 |
| Motor Construction | Stainless steel, oil-free, submersible motor across all configurations |
| Spray Pattern | Center stream with four angled side jets at 45 degrees (clover-shaped display) |
| Center Stream Height Range | 20' (1/2 HP) to 70' (3 HP) |
| Side Jets Width Range | 15' (1/2 HP) to 80' (3 HP) |
| Overall Spray Size Range | 20' H x 30' W (1/2 HP) to 70' H x 80' W (3 HP) |
| Flow Rate Range | 3,600 GPH (1/2 HP) to 10,200 GPH (3 HP) |
| Best for Pond Size | 1/8 acre through 2+ acres depending on motor |
| Minimum Water Depth | 36" (1/2 HP) to 64" (3 HP) |
| Amp Draw Range | 5.0A to 13.3A depending on configuration |
| Saltwater Approved | Yes, no added equipment required |
| Continuous Operation | 24-hour rated, no maintenance required, no control box needed on smaller motors |
| Year-Round Installation | Yes. Winter-safe, no winterizing needed. Freezing water does no damage. |
| Anchoring | Proper anchoring required with two weights or concrete blocks and two nylon ropes. Minimum 20 lbs to 55 lbs per anchor depending on motor. Anchors and mooring line not included. |
| Power Cord | Submersible, 12 GA (70') on motors up to 1.5 HP; 10 GA (100') on 2 and 3 HP. 115V models include a plug. |
| Electrical Requirement | Dedicated GFCI-protected circuit, no extension cords. 115V plugs into standard outlet; 230V is hardwired. |
| Motor Speed / Frequency | 60 Hz, single-phase |
| Optional Accessories | Night Glo warm white LED light kits, color-changing LED light kits (with remote), fountain timers (115V and 230V), mooring lines, and longer power cords |
| ARL Tested | ARL tested and approved to be in compliance with the applicable requirements of UL and the National Electric Code as complete packages. |
| Warranty | 5 years unconditional against motor defects in materials or workmanship under normal operating conditions, and 1 year against factory defects on all other product components. Warranty replacement requires return of the defective unit to the factory with shipping prepaid by the customer for inspection before replacement parts are issued. |
| Made in the USA | Yes (Holland, Michigan) |
Manual
Click to view the Clover Fountain Manual